Once again on the pegged skirt

posted in: Designing | 10

I know I have written quite a lot about my peg skirt experiments, but there is not much information available on the internet about draping a pegged skirt. So if anyone out there wants to try a draped one (as opposed to flat pattern cutting) this post may be useful. I do recognise these posts are not to everyone’s taste, so please feel free to skip it. However I have found this so interesting and I would urge you (if you have a mannequin, or even a friend or relative that you can pin fabric to) to have a go. I am therefore labouring the point a little as some readers are interested in how this works. Despite it’s flaws I enjoy wearing this skirt.

Draped peg skirt Fabrickated
It”s a beautiful day!

Mary Funt, who is a legend, supported by the magnificent Mrs Mole, suggested that the method I had adopted (draping from the CB or CF) was not going to give me a good result. Here is Mrs M’s comment:

I’m with Mary as I was trying to imagine where the side seams should be and being left with some sort of weird poking out edges, Maybe the fabric is just not the right one to be messing with? Would this work with something more drapey and airy? All those pleats and darts are supposed to help you, not create problems.

Well my first attempt at pleating a full skirt was very hard work, but I liked the skirt. It is different to the average, run-of-the-mill skirt. I liked the fact it didn’t have side seams like the flat pattern cutting methods. Also I wanted a skirt with structure (while I suspect drapey and airy might be nice too!).

I had another go, with calico. Below I explain the process, step by step. It was fun, and it is easy. Doing it this way took no more than 30 minutes.

Here is the introduction to the instructions I was given in class.

A peg skirt is characterised by fullness at the waist line, which tapers to a narrow hem. Shaping at the waist line can be done with tucks, gathers or unpressed pleats. Stiffer fabrics will accentuate the shape. Softer fabrics will fall, creating a more Grecian effect. The peg skirt can be draped with or without a side seam. A side seam is usually used for a more modified silhouette. Draping without a side seam allows for more fullness at the waist and therefore a more extreme shape. We will be draping without a side seam; the straight grain will be placed along the CB.

The steps are (briefly) as follows.

  1. Pin the CB to the stand at the waist, hip and torso
    Draped peg skirt 1
    Pin the selvedge at the CB
  2. Hold the upper edge of calico and wrap to CF (there will be lots of excess at the waistline)
  3. At the CF pull the top edge up, pivoting the hem in towards the body (the CF will be on the bias). This is the crucial and critical step. You can see the edge of the fabric pinned to Camilla’s upper chest.
    Draped peg skirt 2.
    Drape to the CF, lift up to shoulder, pin at CF
  4. Pin at CF
  5. Tie or belt at the waist
    Draping a pegged skirt 3
    Belted (side view)
  6. Adjust fullness as required. Fullness can be at CF or CB only, concentrated at the side, or continue more evenly.
  7. You can create more of a 3D quality to the drape by pulling down more fabric from above the belt (I have illustrated this below, but my pattern will be less exaggerated).
    Draping a pegged skirt 4.
    Pulling additional fabric down to create (exaggerated) 3D look
  8. Mark waistline, pleats/darts/gathers
    draping a peg skirt 5.
    Mark CF and dot the waist [in this case above the belt] (black), pleat tops (green) and where pleats underfold (red)
  9. Remove from the stand, fold in pleats as intended and then draw in the waist
  10. Add seam allowance, trim off excess, replace on stand
    draping a peg skirt 8.
    Cut off excess above waist and to right of CF
  11. Mark the hem from the floor upwards.
    Draping a peg skirt 9.
    Replace on stand and mark hem
  12. You can use your calico as a pattern, or create a paper pattern from this. Be sure to measure the circumference of the hem. The one I have draped here is barely 33″. The red skirt has a circumference at the hem of 35″.  You may need to include a split at the back.
  13. It occurred to me that if I draped this skirt from the CF, instead of the CB, I could then (fabric width permitting) cut the CF on the fold and get back to my one piece skirt, without the attendant problems, reported earlier, about symmetry and fit.

10 Responses

  1. Linde

    Ooooooo you have used my all time favourite The Peg. Your picture looks fantastic and the shape is so beautiful. Another winner.

  2. Anne

    I find these posts very interesting, thank you. I’ll have a go, for the experience, less likely to actually wear it though. You look great in your red skirt.

  3. Jay

    Enjoying these posts – carry on please! The calico looks promising. One passing thought, if the CB is on straight grain that might minimise problems with the skirt ‘seating’ in wear.

  4. Chris

    I’m fascinated with this skirt, and it’s much clearer now – thanks for the follow up. I’m in agreement with Jay above, having the straight grain at the back might control unnecessary stretching. I wasn’t sure if this shape would work on you, but it seems just right, especially keeping the fullness to the front. If I made this for myself , I can imagine moving the pleats and folds more to the side, to give the illusion of more curves!

  5. Stephanie

    Love these posts as they help me to grasp what is going on. Thank you! I also like the way you’ve styled your skirt. 🙂

    • fabrickated

      You have got there very quickly Lynn. One of the skirts is as slim as I dared go – the other is quite voluminous – comfortable but a bit extreme looking. I am making them both up so I will be able to tell you how they are to wear.

Leave a Reply to Chris Cancel reply